DownEaster 11′ Steel Dump Body DED11396
- 10 gauge construction throughout
- Dirt shedding , sloped design at side plate and tailgate top
- Double panel side plates equal over 1/4″ thickness.
- Full depth 3/16″rear corner pillars incorporate recessed lighting, keyhole banjo eyes and lower tailgate pin receiver.
- All lighting is LED rubber mounted and NTEA and Federal compliant.
- 2 1/2″ shorter deck height (9′ only)
- Mounting height of 9.5″ chassis to floor (9′ only)
- 10″ board extension pockets ease of install & future optional / custom overhang.
- Self aligning rear latch release for the top gate pins
- Integrated tarp hooks
- DuPont™ Imron® Elite black oven cured paint w/ epoxy primer
FLOOR & UNDERSTRUCTURE
- 4″ x 5.7# Channel long sills and 3″ channel cross members (9′)
- 6″ x 8.2# Channel long sills (10′, 10.5′ 11′)
- 3/16″ Stainless formed 7″ long sills (SS body)
- 3″ stainless tubing, interlaced cross members (SS body)
- Two piece 10 gauge floor with 45 degree slopped corners where meets seamless side plate.
- Greasable Bronze bearings for underbody release mechanisms
TAILGATE
- Formed 10 gauge inner, outer and end panels.
- 1″ hardened pins, (1″ Stainless) with plasma cut latch receiving lock fingers
- Adjustable 1/4″ chain for spreading aggregate material & holding gate in down position
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
DownEaster 12′ Landscape Dump Body DELD1296
- 5″ x 6.7# Channel long sills
- 3″ x 4.1# Channel cross members
- 10GA floor, 2 pc
- 12GA side plates & bulkhead
- 52″ Curb side door, standard
- Structural tubing corner posts
- 3/16″ thick rear cross member/apron with
- tail and reverse light knockouts
- 3/8″ D rings at each inside corner
- All lighting is LED rubber mounted and NTEA and Federal
- compliant.
- Class 20 & 40 (single cylinder) hoists available
- Mounted & painted Sub frame for ease of installation
- Mounting hardware and brackets provided
- Epoxy primer with Phosphate prewash
- Imron® Elite black oven
- cured paint w/ epoxy primer
- Cab Shield
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 12′ Roll-off Frame SH1512EW-G2
- Low profile sub frame and mounting height
- 6″ bore x 15″ stroke hoist, standard.
- 50 deg. Dump angle (10 ton) (13″ high side w/ drive on gate)
- 6″ x 2″ structural tube frame.
- Auto locking body latch w/ ergonomic pull handle.
- Warn 15K electric industrial winch w/ tensioner
- 303 Stainless side rollers pressed over greaseless bronze bearings
- 303 Stainless rear rollers pressed over DOM steel
- with greaseless/replaceable stainless shafts
- Stainless steel side guide rails
- Exterior mounted body prop
- Stainless Steel pump cover
- Spacer plates between upper & lower frames minimizes rust contact points
- “Winch-in” stop switch
- Able to accept other body brands
- 30′ EIPS 1/2″ cable w/ 4.5 ton swivel hook
- Nylon cable roller, self lubricating, for less cable wear
- 4 button, in cab, control pendant
- 1/0 GA battery cables w/ 600 amp fuse
- PPG cured paint w/ corrosion resistant epoxy primer
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 11′ Dump Body with 13″ Drop Sides DESH1196 DBD3
- Available in 9′ and 11′
- 10 GA flooring
- 10 GA side plates
- 3-5 yard
- 13″ high drop sides
- 4 D-rings
- 24″ high drive on tailgate w/ latch
- 38″ bulkhead
- Front handle release lower latch
- Steel rear rollers
- Stainless steel tailgate latch
- PPG cured paint w/ corrosion
- resistant epoxy primer
- Standard Features
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 12′ Container Body DESH1250 SDT-S
- Single door
- 3″ Structural channel
- cross members spaced 16″ on center
- Floor constructed with 10 GA steel
- Front, side, & gate panels
- constructed with 12 GA steel
- Doors constructed with 3″x 3″ tubing
- Rear posts constructed with 3/16″ steel
- Front & side top rails constructed with
- 3″x 3″ tubing
- PPG cured paint w/ corrosion resistant epoxy primer
- Steel ground rollers
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2025 DownEaster 11′ Stainless Dump Body DEDS11396
- 10 gauge construction throughout
- Dirt shedding , sloped design at side plate and tailgate top
- Double panel side plates equal over 1/4″ thickness.
- Full depth 3/16″rear corner pillars incorporate recessed lighting, keyhole banjo eyes and lower tailgate pin receiver.
- All lighting is LED rubber mounted and NTEA and Federal compliant.
- 2 1/2″ shorter deck height (9′ only)
- Mounting height of 9.5″ chassis to floor (9′ only)
- 10″ board extension pockets ease of install & future optional / custom overhang.
- Self aligning rear latch release for the top gate pins
- Integrated tarp hooks
- DuPont™ Imron® Elite black oven cured paint w/ epoxy primer
FLOOR & UNDERSTRUCTURE
- 4″ x 5.7# Channel long sills and 3″ channel cross members (9′)
- 6″ x 8.2# Channel long sills (10′, 10.5′ 11′)
- 3/16″ Stainless formed 7″ long sills (SS body)
- 3″ stainless tubing, interlaced cross members (SS body)
- Two piece 10 gauge floor with 45 degree slopped corners where meets seamless side plate.
- Greasable Bronze bearings for underbody release mechanisms
TAILGATE
- Formed 10 gauge inner, outer and end panels.
- 1″ hardened pins, (1″ Stainless) with plasma cut latch receiving lock fingers
- Adjustable 1/4″ chain for spreading aggregate material & holding gate in down position
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 11′ Drive-on Platform Body with Dovetail DESH1196 PB-DT
- Available in 9′ and 11′
- 38″ bulkhead
- 16″ dovetail
- Corner chain keys
- External stake pockets w/rub rails
- 1/4″ tread plate floor
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2007 JLG 600AJ 4×4 Boom Man Lift
2007 JLG 600AJ
Deutz Diesel Motor
Hour meter reads: 3,845 hours
4×4
Power to Platform
-Sky Power Genest onboard
-110/230v
Airline to Basket
60’ Platform Height / 66’ Working Height
39’9” Horizontal Reach
6’ Jib
8’ Man Basket
Self-Leveling
Rated Gradeability: 45%
Foam Filled Tires
Good tires all around!
Operating Weight: 24,028lbs
Unit was Serviced!
Boom will be ANSI OSHA Inspected before sold!
2016 MEC 4069ERT 4×4 Rough Terrain Scissor Lift
2016 MEC 4069ERT
Electric Powered
Hour Meter Reads: 417 Hours
4×4
Platform Height: 40’
Working Height: 46’
Maximum Drive Height: 40’
Platform Rated Capacity: 800lbs
Machine Weight: 11,000lbs
Gradeability: 40%
Slide Out Deck Extension
Power to Platform
Dimensions: 10’7”x5’9”x9’
Recent Comments