2025 DownEaster 8′ Dump insert IP100-21 W/ cab shield
- 12 gauge floor / 14 gauge side plates
- Two way tailgate (top/bottom hinged) with steel sub frame
- Electric over hydraulic pump with 10′ pendant control cord. & pre punched tarp mounting holes
- Spring loaded tailgate bottom release pins.
- Adjustable 3/16″ chain for spreading aggregate material & holding gate in down position
- Compact scissor hoist with 3.5″ diameter cylinder
- 47 degree dump angle
- Internal stake pockets
- DuPont™ Imron® Elite black oven cured paint with epoxy primer
- Double acting pump (power up / power down)
- 5 Year Warranty
- 2.0 cu yards
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2025 Duramag Aluminum Flatbed TB08184-AL Truck Body
- All Extruded 6005 T6 Alum Box Tube Construction
- Long Sills to Compensate for Hump in Truck Frame
- G-Tube Perimeter Frame
- Extruded Aluminum Headboard w/Accessory Track
- OEM Plug & Play Wire Harness – Body End
- Cast Aluminum Fuel Fill Dish – Streetside Fronts
- 12″ Diamond Plate Apron
- 2×3.188 Long Sills
- 1.5″ x 3.125 Cross Members, 16″ OC
- T&G Extruded Alum Flooring
- All Pre-Wired w/LED Lights Inside Box Tube
- Stake Pockets & Rub Rail
- Lighted Headboard
*SUBFRAME SOLD SEPARATELY
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2025 Duramag Aluminum Dump Bed DB0969520SS
- All Extruded 6005 T6 Aluminum Construction
- 2×6 .250 Long Sills
- Extruded Unibody Floor with 2.5″ OC Bracing
- Rugged & Attractive Formed Side Walls
- Double Walled Sides (Eliminates Cargo Impact Printing)
- HD 4×6 .188 Rear Corner Posts
- Double Walled Tailgate with Stainless Hinge Pins
- Stainless Tailgate Actuator Hardware & Fasteners
- All Pre Wired with LED Lights Inside Box Tube
- 16″ Aluminum Cab Shield
- Manual Tarp Kit
- 20″ Sides
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
DownEaster 11′ Steel Dump Body DED11396
- 10 gauge construction throughout
- Dirt shedding , sloped design at side plate and tailgate top
- Double panel side plates equal over 1/4″ thickness.
- Full depth 3/16″rear corner pillars incorporate recessed lighting, keyhole banjo eyes and lower tailgate pin receiver.
- All lighting is LED rubber mounted and NTEA and Federal compliant.
- 2 1/2″ shorter deck height (9′ only)
- Mounting height of 9.5″ chassis to floor (9′ only)
- 10″ board extension pockets ease of install & future optional / custom overhang.
- Self aligning rear latch release for the top gate pins
- Integrated tarp hooks
- DuPont™ Imron® Elite black oven cured paint w/ epoxy primer
FLOOR & UNDERSTRUCTURE
- 4″ x 5.7# Channel long sills and 3″ channel cross members (9′)
- 6″ x 8.2# Channel long sills (10′, 10.5′ 11′)
- 3/16″ Stainless formed 7″ long sills (SS body)
- 3″ stainless tubing, interlaced cross members (SS body)
- Two piece 10 gauge floor with 45 degree slopped corners where meets seamless side plate.
- Greasable Bronze bearings for underbody release mechanisms
TAILGATE
- Formed 10 gauge inner, outer and end panels.
- 1″ hardened pins, (1″ Stainless) with plasma cut latch receiving lock fingers
- Adjustable 1/4″ chain for spreading aggregate material & holding gate in down position
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
DownEaster 12′ Landscape Dump Body DELD1296
- 5″ x 6.7# Channel long sills
- 3″ x 4.1# Channel cross members
- 10GA floor, 2 pc
- 12GA side plates & bulkhead
- 52″ Curb side door, standard
- Structural tubing corner posts
- 3/16″ thick rear cross member/apron with
- tail and reverse light knockouts
- 3/8″ D rings at each inside corner
- All lighting is LED rubber mounted and NTEA and Federal
- compliant.
- Class 20 & 40 (single cylinder) hoists available
- Mounted & painted Sub frame for ease of installation
- Mounting hardware and brackets provided
- Epoxy primer with Phosphate prewash
- Imron® Elite black oven
- cured paint w/ epoxy primer
- Cab Shield
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 12′ Roll-off Frame SH1512EW-G2
- Low profile sub frame and mounting height
- 6″ bore x 15″ stroke hoist, standard.
- 50 deg. Dump angle (10 ton) (13″ high side w/ drive on gate)
- 6″ x 2″ structural tube frame.
- Auto locking body latch w/ ergonomic pull handle.
- Warn 15K electric industrial winch w/ tensioner
- 303 Stainless side rollers pressed over greaseless bronze bearings
- 303 Stainless rear rollers pressed over DOM steel
- with greaseless/replaceable stainless shafts
- Stainless steel side guide rails
- Exterior mounted body prop
- Stainless Steel pump cover
- Spacer plates between upper & lower frames minimizes rust contact points
- “Winch-in” stop switch
- Able to accept other body brands
- 30′ EIPS 1/2″ cable w/ 4.5 ton swivel hook
- Nylon cable roller, self lubricating, for less cable wear
- 4 button, in cab, control pendant
- 1/0 GA battery cables w/ 600 amp fuse
- PPG cured paint w/ corrosion resistant epoxy primer
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 11′ Dump Body with 13″ Drop Sides DESH1196 DBD3
- Available in 9′ and 11′
- 10 GA flooring
- 10 GA side plates
- 3-5 yard
- 13″ high drop sides
- 4 D-rings
- 24″ high drive on tailgate w/ latch
- 38″ bulkhead
- Front handle release lower latch
- Steel rear rollers
- Stainless steel tailgate latch
- PPG cured paint w/ corrosion
- resistant epoxy primer
- Standard Features
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 12′ Container Body DESH1250 SDT-S
- Single door
- 3″ Structural channel
- cross members spaced 16″ on center
- Floor constructed with 10 GA steel
- Front, side, & gate panels
- constructed with 12 GA steel
- Doors constructed with 3″x 3″ tubing
- Rear posts constructed with 3/16″ steel
- Front & side top rails constructed with
- 3″x 3″ tubing
- PPG cured paint w/ corrosion resistant epoxy primer
- Steel ground rollers
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2025 DownEaster 11′ Stainless Dump Body DEDS11396
- 10 gauge construction throughout
- Dirt shedding , sloped design at side plate and tailgate top
- Double panel side plates equal over 1/4″ thickness.
- Full depth 3/16″rear corner pillars incorporate recessed lighting, keyhole banjo eyes and lower tailgate pin receiver.
- All lighting is LED rubber mounted and NTEA and Federal compliant.
- 2 1/2″ shorter deck height (9′ only)
- Mounting height of 9.5″ chassis to floor (9′ only)
- 10″ board extension pockets ease of install & future optional / custom overhang.
- Self aligning rear latch release for the top gate pins
- Integrated tarp hooks
- DuPont™ Imron® Elite black oven cured paint w/ epoxy primer
FLOOR & UNDERSTRUCTURE
- 4″ x 5.7# Channel long sills and 3″ channel cross members (9′)
- 6″ x 8.2# Channel long sills (10′, 10.5′ 11′)
- 3/16″ Stainless formed 7″ long sills (SS body)
- 3″ stainless tubing, interlaced cross members (SS body)
- Two piece 10 gauge floor with 45 degree slopped corners where meets seamless side plate.
- Greasable Bronze bearings for underbody release mechanisms
TAILGATE
- Formed 10 gauge inner, outer and end panels.
- 1″ hardened pins, (1″ Stainless) with plasma cut latch receiving lock fingers
- Adjustable 1/4″ chain for spreading aggregate material & holding gate in down position
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
The KG-XD King of the Grass stand on zero turn mower combines all the best features of a commercial zero turn mower with a stand on unit to work better, faster, smoother, and with more comfort from its sit behind seat. Just lean back against the seat with your feet on the soft ride platform and place your knees against the Dymetrol angled bolster.
New 2023 Spartan KG-XD Stand-on
Engine – Kawasaki 25.5HP
Hours – 1.3
61″ mower deck
100-300 lb Operator Platform
Multi-Function Key Pad with Soft Start
Throttle Next to Parking Brake
Magnetic Pin Height Adjustment
Front & Rear Tie Down Locations
Lean-in Bolster at Optimum Angle
⅝” Thick on Leading Edge of 7 Gauge Deck
Solid Anti-Scalp Wheels on Deck 4 Ag Bearings on Mower Spindle
Rubber Anti-Scrape Mower Chute
Full Beam LED Light
Parker HTJ 12cc Transmissions
Recent Comments