SwapHogg 10′ Container Body SH1012-S
Standard Features
- Single door
- 3″ Structural channel
- cross members spaced 16″ on center
- Floor constructed with 10 GA steel
- Front, side, & gate panels
- constructed with 12 GA steel
- Doors constructed with 3″x 3″ tubing
- Rear posts constructed with 3/16″ steel
- Front & side top rails constructed with
- 3″x 3″ tubing
- PPG cured paint w/ corrosion resistant epoxy primer
- Steel ground rollers
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 14′ Roll-off Frame SH1514EW-G2 SH01315E
Standard Features
- Low-profile subframe and mounting height
- 6″ bore x 15″ stroke hoist, standard.
- 50 deg. Dump angle (10 ton) (13″ high side w/ drive on gate)
- 6″ x 2″ structural tube frame.
- Auto locking body latch w/ ergonomic pull handle.
- Warn 15K electric industrial winch w/ tensioner
- 303 Stainless side rollers pressed over greaseless bronze bearings
- 303 Stainless rear rollers pressed over DOM steel
- with greaseless/replaceable stainless shafts
- Stainless steel side guide rails
- Exterior-mounted body prop
- Stainless Steel pump cover
- Spacer plates between upper & lower frames minimize rust contact points
- “Winch-in” stop switch
- Able to accept other body brands
- 30′ EIPS 1/2″ cable w/ 4.5 ton swivel hook
- Nylon cable roller, self-lubricating, for less cable wear
- 4-button, in-cab, control pendant
- 1/0 GA battery cables w/ 600 amp fuse
- PPG cured paint w/corrosion-resistant epoxy primer
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 10′ Roll-off Frame SH1510EW-G2 SH0915E
Standard Features
- Low-profile subframe and mounting height
- 6″ bore x 15″ stroke hoist, standard.
- 50 deg. Dump angle (10 ton) (13″ high side w/ drive on gate)
- 6″ x 2″ structural tube frame.
- Auto locking body latch w/ ergonomic pull handle.
- Warn 15K electric industrial winch w/ tensioner
- 303 Stainless side rollers pressed over greaseless bronze bearings
- 303 Stainless rear rollers pressed over DOM steel
- with greaseless/replaceable stainless shafts
- Stainless steel side guide rails
- Exterior-mounted body prop
- Stainless Steel pump cover
- Spacer plates between upper & lower frames minimize rust contact points
- “Winch-in” stop switch
- Able to accept other body brands
- 30′ EIPS 1/2″ cable w/ 4.5 ton swivel hook
- Nylon cable roller, self-lubricating, for less cable wear
- 4-button, in-cab, control pendant
- 1/0 GA battery cables w/ 600 amp fuse
- PPG cured paint w/corrosion-resistant epoxy primer
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 12′ Chipper Body DESH1250 SDT-S/CT1294
Standard Features
- 12′ Container with bolt on Chipper top
- Integrated ladder rack
- Vented Side walls
- Single door
- 3″ Structural channel
- cross members spaced 16″ on center
- Floor constructed with 10 GA steel
- Front, side, & gate panels
- constructed with 12 GA steel
- Doors constructed with 3″x 3″ tubing
- Rear posts constructed with 3/16″ steel
- Front & side top rails constructed with
- 3″x 3″ tubing
- PPG cured paint w/ corrosion resistant epoxy primer
- Steel ground rollers
- Compatible with SwapHogg and Switch & Go systems
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2025 Norstar Skirted Flatbed ST0868458 Truck Body
Adjustable Runners 4″ x 38″ – 42″
Standard 24″ OC Cross Members
Diam Plate Steel .125″ Flat Deck w/ GN Cap
Side Stake Pockets & Rub Rail
Standard 3.5″ Tube x 37.75″ Head Rack
Steel Smooth Fenders
Front & Rear Paddle Latch Tool Boxes
2 5/16″ Raw Steel 1″ Raised 30k Ball
4/5/7 Way Plug Rear & 7 Way Plug in Gooseneck Well
Standard LED Light Package
Mud Flap Mounting Brackets L & R
Color: Black
Not sure which truck bed is right for you? Give us a call at 603.417.2112
DOWNEASTER 9′ STEEL DUMP BODY DED09396
Standard Features
- 10 gauge construction throughout
- Dirt shedding , sloped design at side plate and tailgate top
- Double panel side plates equal over 1/4″ thickness.
- Full depth 3/16″rear corner pillars incorporate recessed lighting, keyhole banjo eyes and lower tailgate pin receiver.
- All lighting is LED rubber mounted and NTEA and Federal compliant.
- 2 1/2″ shorter deck height (9′ only)
- Mounting height of 9.5″ chassis to floor (9′ only)
- 10″ board extension pockets ease of install & future optional / custom overhang.
- Self aligning rear latch release for the top gate pins
- Integrated tarp hooks
- DuPont™ Imron® Elite black oven cured paint w/ epoxy primer
FLOOR & UNDERSTRUCTURE
- 4″ x 5.7# Channel long sills and 3″ channel cross members (9′)
- 6″ x 8.2# Channel long sills (10′, 10.5′ 11′)
- 3/16″ Stainless formed 7″ long sills (SS body)
- 3″ stainless tubing, interlaced cross members (SS body)
- Two piece 10 gauge floor with 45 degree slopped corners where meets seamless side plate.
- Greasable Bronze bearings for underbody release mechanisms
TAILGATE
- Formed 10 gauge inner, outer and end panels.
- 1″ hardened pins, (1″ Stainless) with plasma cut latch receiving lock fingers
- Adjustable 1/4″ chain for spreading aggregate material & holding gate in down position
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2026 DURAMAG S-SERIES ALUMINUM UTILITY BED LONG BED
- Standard Features
- All Aluminum Extruded Box Tube Construction
- Fully Welded Construction – No Bolts to Come Loose
- Extreme Duty .625″ Interlocking Extruded Flooring
- Heavy Slam Latch Tailgate
- Inner Bed Walls & Top of Compartments 3/16″ Smooth Sheet
- One Piece Sides
- Welded Fender Flares – Superior Strength & Rigidity
- Tread Plate Splash Guards on Front
- 40″ Compartment Height
- Radius Corner Traditional Swing Doors
- Blind Compression T-Handles
- Heavy Duty Hidden Hinges
- Adjustable Shelf Brackets in All Compartments (One Shelf Included in Each Compartment)
- Pass Through Panel Between Rear & Center Compartments
- LED Marker Lights, Installed
- LED Penny Lights for Compartments, Installed
- Ultra-Thin 5.5″ LED STT/BU Body Lights, Installed
- OEM Plug & Play Wire Harness, Body End Only (Adaptors Sold Separately)
- Powder Coated White, Black or Red
- Upfit Hardware Kit, Shipped Loose
- (1) Cast Aluminum Fuel Fill Dish, Installed (Street-side Front on Pickups / Street-side Rear on Cab Chassis)
Includes subframe and rear bumper. Additional options and features available.
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2026 DURAMAG S-SERIES ALUMINUM UTILITY BED
- Standard Features
- All Aluminum Extruded Box Tube Construction
- Fully Welded Construction – No Bolts to Come Loose
- Extreme Duty .625″ Interlocking Extruded Flooring
- Heavy Slam Latch Tailgate
- Inner Bed Walls & Top of Compartments 3/16″ Smooth Sheet
- One Piece Sides
- Welded Fender Flares – Superior Strength & Rigidity
- Tread Plate Splash Guards on Front
- 40″ Compartment Height
- Radius Corner Traditional Swing Doors
- Blind Compression T-Handles
- Heavy Duty Hidden Hinges
- Adjustable Shelf Brackets in All Compartments (One Shelf Included in Each Compartment)
- Pass Through Panel Between Rear & Center Compartments
- LED Marker Lights, Installed
- LED Penny Lights for Compartments, Installed
- Ultra-Thin 5.5″ LED STT/BU Body Lights, Installed
- OEM Plug & Play Wire Harness, Body End Only (Adaptors Sold Separately)
- Powder Coated White, Black or Red
- Upfit Hardware Kit, Shipped Loose
- (1) Cast Aluminum Fuel Fill Dish, Installed (Street-side Front on Pickups / Street-side Rear on Cab Chassis)
Includes subframe and rear bumper. Additional options and features available.
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
2026 DownEaster 6′6″ Dump insert IP110 W/ cab shield
- 12 gauge floor / 14 gauge side plates
- Two way tailgate (top/bottom hinged) with steel sub frame
- Electric over hydraulic pump with 10′ pendant control cord. & pre punched tarp mounting holes
- Spring loaded tailgate bottom release pins.
- Adjustable 3/16″ chain for spreading aggregate material & holding gate in down position
- Compact scissor hoist with 3.5″ diameter cylinder
- 47 degree dump angle
- Internal stake pockets
- DuPont™ Imron® Elite black oven cured paint with epoxy primer
- Double acting pump (power up / power down)
- 5 Year Warranty
- 1.6 cu yards
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
Used Southco 11′ Chipper Body with Hoist
Single Swing out rear door
Side Storage/toolbox
Dump Hoist
Fits 9’4″ cab and chassis with 60″ cab to axle.
We will install the body for an additional price
Recent Comments