SwapHogg 12′ Container Body DESH1250 SDT-S
- Available in 10′ (11.5 yard) and 12′ (13 yard)
- Single door
- 3″ Structural channel
- cross members spaced 16″ on center
- Floor constructed with 10 GA steel
- Front, side, & gate panels
- constructed with 12 GA steel
- Doors constructed with 3″x 3″ tubing
- Rear posts constructed with 3/16″ steel
- Front & side top rails constructed with
- 3″x 3″ tubing
- PPG cured paint w/ corrosion resistant epoxy primer
- Steel ground rollers
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
DownEaster 11′ Stainless Dump Body DEDS11396
- 10 gauge construction throughout
- Dirt shedding , sloped design at side plate and tailgate top
- Double panel side plates equal over 1/4″ thickness.
- Full depth 3/16″rear corner pillars incorporate recessed lighting, keyhole banjo eyes and lower tailgate pin receiver.
- All lighting is LED rubber mounted and NTEA and Federal compliant.
- 2 1/2″ shorter deck height (9′ only)
- Mounting height of 9.5″ chassis to floor (9′ only)
- 10″ board extension pockets ease of install & future optional / custom overhang.
- Self aligning rear latch release for the top gate pins
- Integrated tarp hooks
- DuPont™ Imron® Elite black oven cured paint w/ epoxy primer
FLOOR & UNDERSTRUCTURE
- 4″ x 5.7# Channel long sills and 3″ channel cross members (9′)
- 6″ x 8.2# Channel long sills (10′, 10.5′ 11′)
- 3/16″ Stainless formed 7″ long sills (SS body)
- 3″ stainless tubing, interlaced cross members (SS body)
- Two piece 10 gauge floor with 45 degree slopped corners where meets seamless side plate.
- Greasable Bronze bearings for underbody release mechanisms
TAILGATE
- Formed 10 gauge inner, outer and end panels.
- 1″ hardened pins, (1″ Stainless) with plasma cut latch receiving lock fingers
- Adjustable 1/4″ chain for spreading aggregate material & holding gate in down position
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
SwapHogg 11′ Drive-on Platform Body with Dovetail DESH1196 PB-DT
- Available in 9′ and 11′
- 38″ bulkhead
- 16″ dovetail
- Corner chain keys
- External stake pockets w/rub rails
- 1/4″ tread plate floor
Installation is available!
Not sure which truck bed is right for you? Give us a call at 603.417.2112
- Brand New 8’ S- Series Single Wheel Duramag Utility Service Pickup Bed
-For GM Chassis 2020 and Up
All Aluminum (6000 Series) Understructure with Extruded Box Tube
Heavy Slam Latch Tailgate with Stainless Steel Lock Rods
Swing Doors with Nitrogen Props on Vertical Compartments
Black Polymer Rivet less Door Handles
Extreme Duty (6000 Series) .625 Interlocking Extruded Aluminum Floor
Fully Welded Construction – No Rivets, Screws, or Bolts to Come Loose
Welded Fender Flares for Superior Strength and Rigidity
LED Marker Lights (where required)
LED Penny Light in Each Compartment
LED Ultra-thin 6” Round Stop/Turn/Tail/Backup Body Lights
Inner Bed Walls and Exterior Top of Compartments – 1/8” Diamond Plate
Continuous Aluminum Piano Door Hinge
Adjustable Shelving in Front, Middle, and Rear Compartments (one shelf with dividers in each compartment)
Pass-through Panel between Front & Center Compartments
Tread Plate Splash Guards on Front Wall
NEVER BEEN MOUNTED
MSRP of this bed is $6,895!!!
Recent Comments