Portfolio Tag: landscape equipment

2025 DEDS09396 2.5-5 yard, STAINLESS, DownEaster 9′ Dump Body with CS615 Hoist

• 10 gauge construction throughout
• Dirt shedding , sloped design at side plate and tailgate top
• Double panel side plates equal over 1/4″ thickness.
• Full depth 3/16″rear corner pillars incorporate recessed lighting, keyhole banjo eyes and lower tailgate pin receiver.
• All lighting is LED rubber mounted and NTEA and Federal compliant.
• 2 1/2″ shorter deck height (9′ only)
• Mounting height of 9.5″ chassis to floor (9′ only)
• 10″ board extension pockets ease of install & future optional / custom overhang.
• Self aligning rear latch release for the top gate pins
• Integrated tarp hooks
• DuPont™ Imron® Elite black oven cured paint w/ epoxy primer

FLOOR & UNDERSTRUCTURE

• 4″ x 5.7# Channel long sills and 3″ channel cross members (9′)
• 6″ x 8.2# Channel long sills (10′, 10.5′ 11′)
• 3/16″ Stainless formed 7″ long sills (SS body)
• 3″ stainless tubing, interlaced cross members (SS body)
• Two piece 10 gauge floor with 45 degree slopped corners where meets seamless side plate.
• Greasable Bronze bearings for underbody release mechanisms

TAILGATE

• Formed 10 gauge inner, outer and end panels.
• 1″ hardened pins, (1″ Stainless) with plasma cut latch receiving lock fingers
• Adjustable 1/4″ chain for spreading aggregate material & holding gate in down position

Installation is available!

Not sure which truck bed is right for you? Give us a call at 603.417.2112

SwapHogg 11′ Drive-on Platform Body with Dovetail DESH0996 PB-DT

• Available in 9′ and 11′
• 38″ bulkhead
• 16″ dovetail
• Corner chain keys
• External stake pockets w/rub rails
• 1/4″ tread plate floor

Installation is available!

Not sure which truck bed is right for you? Give us a call at 603.417.2112

SwapHogg 14′ Container Body SH1415-S

• Single door
• 3″ Structural channel
• cross members spaced 16″ on center
• Floor constructed with 10 GA steel
• Front, side, & gate panels
• constructed with 12 GA steel
• Doors constructed with 3″x 3″ tubing
• Rear posts constructed with 3/16″ steel
• Front & side top rails constructed with
• 3″x 3″ tubing
• PPG cured paint w/ corrosion resistant epoxy primer
• Steel ground rollers

Installation is available!

Not sure which truck bed is right for you? Give us a call at 603.417.2112

SwapHogg 10′ Container Body SH1012-S

• Single door
• 3″ Structural channel
• cross members spaced 16″ on center
• Floor constructed with 10 GA steel
• Front, side, & gate panels
• constructed with 12 GA steel
• Doors constructed with 3″x 3″ tubing
• Rear posts constructed with 3/16″ steel
• Front & side top rails constructed with
• 3″x 3″ tubing
• PPG cured paint w/ corrosion resistant epoxy primer
• Steel ground rollers

Installation is available!

Not sure which truck bed is right for you? Give us a call at 603.417.2112

Low profile sub frame and mounting height

6″ bore x 15″ stroke hoist, standard.

50 deg. Dump angle (10 ton) (13″ high side w/ drive on gate)

6″ x 2″ structural tube frame.

Auto locking body latch w/ ergonomic pull handle.

Warn 15K electric industrial winch w/ tensioner

303 Stainless side rollers pressed over greaseless bronze bearings

303 Stainless rear rollers pressed over DOM steel

with greaseless/replaceable stainless shafts

Stainless steel side guide rails

Exterior mounted body prop

Stainless Steel pump cover

Spacer plates between upper & lower frames minimizes rust contact points

“Winch-in” stop switch

Able to accept other body brands

30′ EIPS 1/2″ cable w/ 4.5 ton swivel hook

Nylon cable roller, self lubricating, for less cable wear

4 button, in cab, control pendant

1/0 GA battery cables w/ 600 amp fuse

PPG cured paint w/ corrosion resistant epoxy primer